hazardous-area LED procurement should distinguish IECEx and ATEX while checking market, zone, model scope, temperature class, marking and installation files. Improve useful illuminance and reduce glare or dark zones through optics, spacing and aiming control. This article covers site inputs, specific product directions, photometric checks, implementation and acceptance for B2B industrial lighting projects.
Who this guide is for
This guide is for procurement teams, factory and warehouse managers, lighting designers, electrical contractors and project owners who need a traceable industrial LED lighting decision.
Use it for factories, workshops, warehouses, logistics centers, cold rooms, food or pharmaceutical plants, chemical areas, industrial parks, ports, airports, tunnels and sports facilities where the relevant site conditions are confirmed.
Key industrial lighting selection factors
- Mounting height and illuminance: define the work plane and target lux before choosing wattage.
- Optics and glare: compare beam angle, spacing, aiming, uniformity and visual comfort together.
- Protection and temperature: verify IP/IK, sealing, corrosion, low-temperature start or hazardous-area limits.
- Controls and maintenance: confirm DALI, 0-10V, sensors, manual override, driver access and spare parts.
- Commercial scope: compare manufacturer, model, price, warranty, delivery, installation and commissioning on the same basis.
Recommended product types
Select product types from the application first, then match actual parameters, photometric files, installation details and project documents.
Common selection mistakes
- Comparing wattage or unit price without a lighting calculation or pilot test.
- Using a standard luminaire in a cold, wet, corrosive, cleanroom or hazardous environment without verification.
- Ignoring glare, flicker, vertical illuminance, rack shadows or boundary spill light.
- Leaving mounting, wiring, controls, service access and acceptance records out of the quotation scope.
Project inquiry: Send site photos, area, mounting height, target lux, operating hours, environment and preferred control method.
IECEx and ATEX serve different international or regional conformity contexts. Certificates, reports, markings, datasheets, model suffixes and delivered products must be reviewed for the destination market.
Define the site conditions first
Confirm dimensions, clear height, mounting positions, obstructions, work-plane height, electrical circuits, operating hours and the existing fixture baseline. Add temperature, moisture, dust, corrosion, cleanroom or hazardous-area requirements where relevant.
Project details to confirm first
If the project brief is still incomplete, consolidate it into a one-page input sheet before asking for a quotation. This keeps supplier replies comparable and reduces repeated back-and-forth.
- Application area, process rhythm and daily operating hours.
- Mounting height, pole positions, obstructions and service access.
- Temperature, moisture, dust, corrosion or hazardous-area limits.
- Target illuminance, uniformity and glare limits for each zone.
- Control method, dimming range, fallback behavior and manual override.
- Acceptance records, drawings, photos, wiring notes and maintenance files.
Start with the site, then move to lighting parameters, then lock the acceptance scope.
Industrial lighting products and search terms
Relevant product directions include LED Explosion-Proof Platform Light, LED Explosion-Proof Floodlight. These product names help establish a comparison range; final wattage, optics, protection rating and quantity must be checked against the actual site.
LED product names and common procurement queries
These phrases summarize recurring Baidu autocomplete directions in China. They are organized as buyer questions, not exact search-volume claims or brand rankings.
LED High Bay Light
Common queries：LED high bay manufacturer, 100W LED high bay, 150W high bay model, 200W high bay price, high bay mounting height
Use mounting height, target lux, optics, temperature and controls before comparing wattage, model and price.
LED Explosion-Proof Light
Common queries：LED explosion-proof light manufacturer, explosion-proof LED model, hazardous-area LED fixture
Provide zone, gas or dust, temperature class, mounting, cable entry, wattage and optics before selection.
LED Cold Storage Light
Common queries：LED cold storage solution, freezer LED light, cold-room wiring, low-temperature luminaire
Confirm minimum temperature, cold start, condensation, aisle optics, sensing and maintenance safety.
LED Floodlight
Common queries：LED floodlight manufacturer, LED floodlight wiring, industrial floodlight price, LED floodlight driver
Review throw, pole position, optics, aiming, glare, surge protection and bracket loading before wattage.
LED Road Light
Common queries：LED street light manufacturer, LED road light wattage, 100W street light, IP65 road light
Road width, pole height, spacing, optics, uniformity and dimming determine the model.
Comparison and quotation scope
When comparing suppliers, keep model, actual power, efficacy, optics, protection rating, driver, warranty, delivery, installation and control scope in the same table. For high bays, hazardous-area luminaires, tri-proof units, cleanroom lights, cold-storage lights, floodlights and road lights, make sure the sample, photometric file and accessories match the quotation.
If the brief is still conceptual, write a one-page project sheet first: application, area, clear height, environment, target lux, control method, budget and delivery timing. This makes quotation responses easier to compare and supports pilot testing and acceptance later.
Illuminance, efficacy and optical distribution
Efficacy indicates electrical efficiency, while optical distribution determines where the light reaches the working plane. Review beam angle, spacing, aiming, reflection and maintenance factor together instead of comparing wattage only.
Construction, protection and controls
Check thermal design, driver, voltage, power factor, surge protection, sealing, cable entry, mounting and service access. Sensor dimming and zoning should also be tested for trigger range, delay, minimum output and failure fallback.
Implementation workflow
- Record the existing illuminance, power, layout and operating baseline.
- Select construction, output, optics and controls from the site conditions.
- Validate a representative pilot area.
- Adjust spacing, aiming or controls before full installation.
- Repeat measurements and archive commissioning records.
Improve useful illuminance and reduce glare or dark zones through optics, spacing and aiming control.
Project Checklist
- Confirm site inputs for optics, glare and uniformity
- Record design assumptions and measurable acceptance criteria
- Check installation, controls and maintenance access
- Archive product data, commissioning results and follow-up actions
Project documentation advice
Keep datasheets, photometric files, quotations, inspection reports, installation drawings, wiring diagrams, control notes, acceptance records and spare-part lists together so the project can be reviewed later without extra cleanup. For news content, use specific product names and site conditions rather than repeating the generic phrase “industrial lighting” too often.
Major Chinese standards for project review
Standard status was reviewed against official Chinese platforms on 2026-08-11. Confirm the current edition, implementation date, local requirements and contract scope before use.
GB/T 7000.1-2023Luminaires - Part 1: General Requirements and Tests
Current luminaire safety and test basis, effective from 1 January 2026.
Official recordGB/T 31897.201-2025Luminaire Performance - Particular Requirements for LED Luminaires
Current particular performance requirements for LED luminaires, effective from 1 May 2026.
Official recordGB/T 5700-2023Methods of Measuring Lighting
Lighting measurement methods with project-specific points, instruments, environment and control state.
Official recordGB/T 4208-2017Degrees of Protection Provided by Enclosure (IP Code)
Check dust and water protection; IP does not prove corrosion, low-temperature or explosion protection.
Official recordGB/T 17743-2021Radio Disturbance from Electrical Lighting
Limits and measurement methods for radio disturbance from lighting equipment.
Official recordFrequently asked questions
Can the old fixture be replaced at the same wattage?
Not reliably. Efficacy, optics, mounting height and depreciation differ, so target illuminance and layout should be checked again.
What is needed for a quotation?
Provide the application, area, mounting height, photos, target lux, environment and operating hours.
How should suppliers be compared?
Use the same site assumptions and compare model, power, efficacy, optics, protection, driver, warranty, delivery, installation and control scope.
Primary international sources
Publisher pages can change. Verify the current version, destination market and project applicability before procurement.
Contact Suzhou Yaoqian Intelligent Technology Co., LTD
Since 2006, Suzhou Yaoqian Intelligent Technology Co., LTD has worked on LED sources, thermal design, optics, industrial luminaires and smart controls, supporting product selection and project coordination.
Contact: Mr. Xie · +86 13915532167 · xieming113@163.com