Industrial LED lighting should be selected by application. Factories use high bays, cold storage projects need low-temperature and condensation checks, while roads, solar street lights, sports lighting, high-mast and outdoor floodlighting depend on pole layout, optics, glare, protection and maintenance. This guide translates the topic into practical site inputs, product checks, implementation steps and acceptance records for industrial lighting projects in Jiangsu, Zhejiang, Shanghai and the Yangtze River Delta.
Quick Takeaways
This section gives procurement and engineering readers the decision points before the detailed guide.
Match High Bay Light to the site environment before comparing wattage or price.
Area, clear height, mounting position, photos, target lux, operating hours and control needs.
A cheap fixture can fail the project if optics, glare, sealing, driver quality or service access are ignored.
Build a one-page project sheet and validate a pilot zone before full procurement.
Project Review Checklist
Before quotation or design review, prepare these inputs so the fixture model, quantity, mounting method and acceptance scope can be checked on the same basis.
Share dimensions, mounting height, ceiling structure, environment, operating hours and photos.
Confirm target illuminance, uniformity, glare control, color temperature and control requirements.
Compare wattage, efficacy, optics, protection rating, driver, mounting accessories and warranty scope.
Clarify wiring, brackets, installation sequence, commissioning and site safety responsibilities.
Keep measurement points, test status, product documents and maintenance requirements clear.
Use related product and case pages to compare similar site conditions and layout decisions.
Who this guide is for
This guide is for procurement teams, factory and warehouse managers, lighting designers, electrical contractors and project owners who need a traceable industrial LED lighting decision.
Use the guide for factories, workshops, warehouses, logistics centers, cold rooms, food or pharmaceutical plants, chemical areas, industrial parks, ports, airports, tunnels and sports facilities where the relevant site conditions are confirmed.
Key industrial lighting selection factors
- Mounting height and illuminance: define the work plane and target lux before choosing wattage.
- Optics and glare: compare beam angle, spacing, aiming, uniformity and visual comfort together.
- Protection and temperature: verify IP/IK, sealing, corrosion, low-temperature start or hazardous-area limits.
- Controls and maintenance: confirm DALI, 0-10V, sensors, manual override, driver access and spare parts.
- Commercial scope: compare manufacturer, model, price, warranty, delivery, installation and commissioning on the same basis.
Recommended product types
Recommended product types should be selected from the application first, then matched with actual parameters, photometric files, installation details and project documents.
Common selection mistakes
- Comparing wattage or unit price without a lighting calculation or pilot test.
- Using a standard luminaire in a cold, wet, corrosive, cleanroom or hazardous environment without verification.
- Ignoring glare, flicker, vertical illuminance, rack shadows or boundary spill light.
- Leaving mounting, wiring, controls, service access and acceptance records out of the quotation scope.
Project inquiry: For a quotation, send site photos, area, mounting height, target lux, operating hours, environment and preferred control method. Yaoqian Lighting can return a product shortlist, layout discussion and project document checklist.
Define the project problem first
Industrial lighting should not be specified by wattage alone. The project brief should define mounting height, work-plane illuminance, uniformity, glare limits, environmental protection, controls, maintenance access and budget boundaries.
The same requirements should be used for supplier comparison, pilot testing and final acceptance so that product claims can be checked against measurable site results.
Project details to confirm first
If the project brief is still incomplete, consolidate it into a one-page input sheet before asking for a quotation. This keeps supplier replies comparable and reduces repeated back-and-forth.
- Application area, process rhythm and daily operating hours.
- Mounting height, pole positions, obstructions and service access.
- Temperature, moisture, dust, corrosion or hazardous-area limits.
- Target illuminance, uniformity and glare limits for each zone.
- Control method, dimming range, fallback behavior and manual override.
- Acceptance records, drawings, photos, wiring notes and maintenance files.
Start with the site, then move to lighting parameters, then lock the acceptance scope.
Selection Matrix by Application
| Application | Product direction | Key review points |
|---|---|---|
| Factory / warehouse | LED high bay or UFO high bay | Height, optics, glare, driver, maintenance access |
| Cold storage / freezer | LED cold-storage light | Low-temperature start, condensation control, IP rating, rack shadows |
| Wet, dusty or clean areas | Tri-proof or cleanroom light | Sealing, cleanability, corrosion resistance, mounting and service |
| Hazardous area | LED explosion-proof light | Zone/classification, temperature class, cable entry, certificates and markings |
| Yard, road or loading area | Floodlight, area light or road light | Pole height, aiming, spill light, surge protection and controls |
Major Chinese standards for project review
Standard status reviewed against official Chinese platforms on 2026-08-25. Confirm the current edition, implementation date, local requirements and contract scope before design, procurement or acceptance.
GB 50034-2013Standard for Lighting Design of Buildings
Design reference for illuminance, uniformity, glare, color rendering, lighting power density and controls.
Official recordGB/T 5700-2023Methods of Measuring Lighting
Methods for lighting measurements; projects should also define points, instruments, environment and control state.
Official recordGB/T 7000.1-2023Luminaires - Part 1: General Requirements and Tests
Current general luminaire safety and test basis, effective from 1 January 2026.
Official recordGB/T 31897.201-2025Luminaire Performance - Part 2-1: Particular Requirements for LED Luminaires
Current particular performance requirements for LED luminaires, effective from 1 May 2026.
Official recordGB/T 4208-2017Degrees of Protection Provided by Enclosure (IP Code)
Defines enclosure dust and water protection; an IP rating does not prove corrosion, low-temperature or explosion protection.
Official recordSite survey and input checklist
Prepare drawings, dimensions, clear height, fixture positions, structural obstructions, work-plane height, electrical circuits, operating hours and the quantity and wattage of existing luminaires. Add temperature, moisture, dust, corrosion, cleanroom or hazardous-area information where relevant.
- Separate factory, warehouse, cold-room and road scenarios
- Compare wattage, efficacy, optics and protection on the same basis
- Confirm pole layout and glare for sports, high-mast and outdoor lighting
- Match product pages and case pages to actual site conditions
Illuminance, efficacy and optical distribution
Efficacy indicates how efficiently electrical power is converted into light, but optical distribution determines where that light reaches the working plane. Beam angle, spacing, aiming direction, reflection and maintenance factor should be reviewed together.
For high bays, rack aisles, roads, yards and long-throw applications, use photometric files, lighting calculations or a pilot installation instead of comparing wattage or nominal lumens only.
Construction, protection and controls
Check thermal design, driver, input voltage, power factor, surge protection, sealing, cable entry, mounting and service access. Special environments require project-specific confirmation of material, coating, low-temperature, corrosion or explosion-protection limits.
Sensor dimming and zoning can reduce idle energy, but commissioning should also verify trigger range, delay, minimum output, manual override and failure fallback.
Implementation and acceptance workflow
- Record the existing illuminance, power, layout and operating baseline.
- Select product construction, output, optics and controls from the site conditions.
- Test a representative pilot area and adjust spacing, aiming or control settings.
- Complete phased installation with documented safety and shutdown arrangements.
- Repeat measurements and archive product, commissioning and maintenance records.
Group products, cases and site parameters by application so buyers can review mounting height, target illuminance, environment and maintenance conditions.
Relevant product directions
Typical product searches for this topic include High Bay Light, Smart Sensor LED Cold Storage Light, LED Tri-Proof Batten Light, Industrial Park LED Road Light, Integrated LED Solar Street Light, Basketball Court LED Light, Badminton Hall High Bay Light, Football Field LED Light, Port High Mast Floodlight, Architectural Lighting, Ultra-Thin LED Edge-Lit Panel Light, IP65 Ultra-Thin Cleanroom Panel Light, Tunnel Light, LED Tube Light, Parking Lot Floodlight, Explosion Proof Light, LED Landscape Garden Light, Smart-Control UFO LED High Bay Light. Product names define a comparison range; final wattage, optics, protection rating and quantity must be confirmed against the actual site.
Procurement Review Path
Use the same project assumptions when comparing suppliers, product specifications and installation scope.
| Review point | What the buyer checks | Where this page helps |
|---|---|---|
| manufacturer / supplier | Company capability, communication speed and project support | contact block, product links and project checklist |
| price / model / specification | Comparable quotation scope and technical parameters | comparison table, parameter notes and product pages |
| installation / wiring | Mounting, cable entry, control method and maintenance access | implementation workflow and acceptance records |
| LED High Bay Light | factory high bay light / warehouse high bay light / industrial high bay light | Start with mounting height, target lux, optics, temperature and controls before comparing wattage, model and price. |
| LED Cold Storage Light | cold storage light / cold room light / freezer LED light | Confirm minimum temperature, cold start, condensation, rack-aisle optics, sensing and maintenance safety. |
| LED Tri-Proof Light | tri-proof light / cleanroom light / panel light | Translate the tri-proof label into IP rating, materials, sealing, corrosion resistance, mounting and cleaning conditions. |
| LED Road Light | LED street light / solar street light / LED street light manufacturer | Road width, pole height, spacing, distribution, average illuminance or luminance, uniformity and dimming determine the model. |
Related LED luminaires and selection questions
Use product names together with site conditions, mounting height, optics and acceptance requirements when preparing a comparable quotation.
LED High Bay Light
Selection questions：factory high bay light、warehouse high bay light、industrial high bay light、LED high bay light manufacturer、100W LED high bay
Start with mounting height, target lux, optics, temperature and controls before comparing wattage, model and price.
LED Cold Storage Light
Selection questions：cold storage light、cold room light、freezer LED light、cold-room light wiring、low-temperature luminaire
Confirm minimum temperature, cold start, condensation, rack-aisle optics, sensing and maintenance safety.
LED Tri-Proof Light
Selection questions：tri-proof light、cleanroom light、panel light、T8 tube light、parking garage light、LED tri-proof light meaning、tri-proof light mounting、tri-proof wiring、tri-proof light manufacturer
Translate the tri-proof label into IP rating, materials, sealing, corrosion resistance, mounting and cleaning conditions.
LED Road Light
Selection questions：LED street light、solar street light、LED street light manufacturer、LED road light wattage、100W LED street light
Road width, pole height, spacing, distribution, average illuminance or luminance, uniformity and dimming determine the model.
Integrated Solar Street Light
Selection questions：integrated solar street light、solar street light manufacturer、solar street light price、solar street light with pole、solar street light troubleshooting
Quotation should define pole, solar panel, battery, controller, operating hours, autonomy days and foundation scope.
LED Sports Light
Selection questions：basketball court light、football field light、badminton hall light、indoor sports hall lighting、LED sports light、LED sports light manufacturer、400W sports light
Use field size, mast height, indoor or outdoor use, competition level, horizontal and vertical illuminance, glare, flicker and broadcast needs.
LED High-Mast Floodlight
Selection questions：high-mast light、LED high-mast light specification、high-mast floodlight parameters、high-mast manufacturer、port high-mast lighting
Review mast height, lowering system, throw distance, wind load, optics, glare and high-level maintenance.
LED Floodlight
Selection questions：outdoor floodlight、LED floodlight、LED floodlight manufacturer、LED floodlight wiring、industrial floodlight price
Review throw distance, pole position, optics, aiming, glare, surge protection and bracket loading before wattage and quantity.
LED Panel Light
Selection questions：panel light、ultra-thin panel light、LED panel light installation、LED panel wiring、panel light replacement
Confirm ceiling grid, opening, recessed or surface mounting, driver location, efficiency and service access before size and wattage.
LED Cleanroom Light
Selection questions：cleanroom light、cleanroom purification light、cleanroom panel light、custom cleanroom luminaire、cleanroom versus panel light
Review flush surfaces, sealing, cleaning, openings, color quality, flicker and maintenance; a standard panel may not qualify.
LED Tunnel Light
Selection questions：LED tunnel light、parking garage light、tunnel lighting standard、LED tunnel light module、tunnel luminaire wiring
Separate entrance, transition, interior and exit zones, then review luminance, uniformity, dimming, continuous duty and maintenance.
LED Explosion-Proof Light
Selection questions：LED explosion-proof light、LED explosion-proof light manufacturer、explosion-proof LED model、hazardous-area LED fixture、explosion-proof light maintenance
Provide zone, gas or dust, temperature class, mounting, cable entry, wattage and optics before quotation.
Industrial Smart Lighting Control System
Selection questions：smart lighting control wiring、lighting control module、DALI lighting control system、LED dimming controller
Define zones, schedules, sensors, dimming, manual override and fallback before protocol, gateway, modules and permissions.
Comparison and quotation scope
When comparing suppliers, keep model, actual power, efficacy, optics, protection rating, driver, warranty, delivery, installation and control scope in the same table. For high bays, hazardous-area luminaires, tri-proof units, cleanroom lights, cold-storage lights, floodlights and road lights, make sure the sample, photometric file and accessories match the quotation.
If the brief is still conceptual, write a one-page project sheet first: application, area, clear height, environment, target lux, control method, budget and delivery timing. This makes quotation responses easier to compare and supports pilot testing and acceptance later.
Energy Saving and Payback Check
For retrofit articles, calculate energy savings with the same operating assumptions: annual saving = (old total power - new total power) x annual operating hours x electricity price. Then add maintenance reduction, installation cost and control strategy before discussing payback.
Do not treat the formula as a fixed promise; measure the pre-retrofit baseline and verify post-retrofit illuminance before final acceptance.
Selection Questions
How should industrial lighting products be selected by scenario?
Factories and warehouses usually need high bays, linear high bays or tri-proof lights; cold rooms require low-temperature startup and condensation control; roads, courts, high-mast areas and facade projects need pole positions, optics and glare control checked together.
Why should product application news link both product and case pages?
Product pages verify model and specification details, while case pages confirm site conditions, pole positions, aisle layout, obstructions and illuminance targets.
What should a product application article emphasize?
Focus on mounting height, target illuminance, optics, protection, temperature range, controls, acceptance records and matching project cases.
Project documentation advice
Keep datasheets, photometric files, quotations, inspection reports, installation drawings, wiring diagrams, control notes, acceptance records and spare-part lists together so the project can be reviewed later without extra cleanup. For news content, use specific product names and site conditions rather than repeating the generic phrase “industrial lighting” too often.
Contact Suzhou Yaoqian Intelligent Technology Co., LTD
Since 2006, Suzhou Yaoqian Intelligent Technology Co., LTD has worked on LED sources, thermal design, optics, industrial luminaires and smart controls. The team supports product selection, parameter review and project coordination.
Contact: Mr. Xie · +86 13915532167 · xieming113@163.com